paulswamp34

How to Replace a Saab 9-3 Key The Saab 9-3 has an impressive amount of appeal for drivers. It is well-lit and has a strong performance engine. It has a high safety rating. However, it is crucial to ensure that you have at least two working keys for your car. If you lose only one key, it can be very expensive to add a new one. How to Replace the Ignition Key on the Saab 9-3 You'll need to replace your car keys in the event that it isn't turning. This guide will show you how to replace the ignition key on the Saab 9-3. You'll require a replacement key, a new reprogrammable battery, and a new key-fob cover. Unlike older models, most modern Saab automobiles use an electronic transponder inside the key-fob instead of a physical key that can be used to unlock and start the vehicle. The reprogrammable batteries in the key-fob will eventually get worn out, and eventually can't hold any charge. This is especially the case if you use the same key on the same lock. A professional locksmith can change the battery fairly easily. You can also do it yourself if have the right tools and a bit of patience. The first step is to take the key-fob apart. This is done by inserting a flathead screwdriver in the slot that is located in the middle of the case. You must work slowly, since the plastic is extremely thin and easily damaged. After the case has been opened and you are able to prepare the new key by combining the lower part of the key that was used previously with the banana and transponder on the new key. This will ensure that the new key is mated to the CIM properly, which could make a huge difference when replacing the sole key for your Saab 9-3. How to Replace the Ignition Key in a Saab 900 If you don't have two keys, you'll have to remove the dashboard and steering wheel to get to the ignition. Begin by disconnecting the negative battery cable. After the battery has been disconnected, you can take off all the trim pieces as well as dashboard pieces that surround the steering wheel. Once the dash has been taken off, you can push an screwdriver through the hole behind the ignition switch and remove it. The ignition cylinder is equipped with a key lock, which can prevent the vehicle from starting if it does not have the key in it. If the ignition switch on your 900 isn't working, look at the key to see if it's in the lock or stuck in the barrel of the ignition. It's also a good idea to rotate your keys frequently and keep them clean so that they don't get bent. Saab cars differ from other vehicles because they don't use traditional keys made of metal. Instead, the car is able to recognize electric signals from the key fob using the use of a special microchip. If you lose your only working key fob the dealer will charge you the highest dollar to replace your computer module (known as the CIM). We can however reprogram your existing computer's EEPROM to prepare it to accept new keys without replacing it. You'll save more than 50% on the dealer's cost! This is the SAAB KEY PROGRAM. Learn more about it here! How do you replace the ignition Key in the Saab9-5 The metal part of a traditional Saab key is simple to duplicate, and it's not much of a barrier against theft of vehicles. The real security is the electronic component in the key-fob, which is equipped with a chip that detects the car when it is inserted into the ignition switch. Saab's anti-theft system has relied upon this technology for over a decade. It's not as effective as a physical lock on the door, but it does make stealing your own car significantly more difficult. Every Saab owner must keep an extra Saab key in their car. The majority of new Saabs come with two keys, but they are also available for purchase at a dealer using a special handheld device known as Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this is the NG 9-3 vehicles with more modern, more advanced features that require a key-fob. If you lose all keys or keys, the dealer will replace your CIM or TWICE modules, and charge you a premium for it. However, we can reprogram the EEPROM on your computer to accept new keys, without replacing the expensive modules. How do you replace the ignition Key in the Saab XC90 It's probably time to replace your SAAB key fob if you're experiencing issues turning the lock barrel. It's a simple process and you don't even need to visit a dealership. You can do it at home, using a couple of basic tools. First, you'll need to prepare the new key. Before you begin, turn off the anti-theft by placing blocks under the rear wheels and activating your handbrake. Insert the key into the ignition, and then turn it to the “on” position. This will activate the accessories but will not start the engine. Repeat this process five times, then keep the key in the on position. You'll then have to buy a new case for your key fob. They can be found at any auto parts store, and they're generally quite affordable. They can be purchased without electronics, based on the model. To open up the case, insert an flathead screwdriver into the slot that is in the middle, and gently work it. After saab key replacement cost G28 've separated the case, you'll have access to all of the internal electronic components. To take the electronics out, make use of a small screwdriver, and try to pry them out with a gentle force.